济南力诺瑞特太阳能销售服务中心
地址:济南市天桥区粟山路76号(药山派出所对面)
电话:0531-85715890
手机:15665707182
网站:http://www.sdlntyn.com
联系人:江经理
当前位置:首页 - 产品知识产品知识
接线接错也会引发太阳能故障和不正常
来源:http://www.sdlntyn.com 发布时间:2018-3-29 14:08:05 浏览次数:451

太阳能充电控制器是目前用户用的比较多的,它的接线顺序比较复杂,有很多的用户都经常接线接错,这样可能会把控制器造成损坏,严重的还会直接发生火灾等可能。

The solar charging controller is currently used by many users. Its wiring sequence is rather complex. There are many users who often connect the wrong connection. This may cause damage to the controller, and it will also cause a direct fire.

连接蓄电池之前,确保蓄电池电压高于6V 以启动控制器。若系统是24V的,得确保蓄电池电压不低于18V。系统电压选择只有在一次启动控制器时自动识别。

Before connecting the battery, make sure that the battery voltage is higher than 6V to start the controller. If the system is 24V, it is necessary to ensure that the battery voltage is not less than 18V. The system voltage selection is automatically identified only when the first start of the controller.

太阳能控制器的负载端可以连接额定工作电压和蓄电池电压两个相同的直流用电设备,控制器以蓄电池电压给负载供电。

济南力诺瑞特太阳能

The load side of the solar controller can be connected to two identical DC operating devices, rated working voltage and battery voltage, and the controller is powered by battery voltage to load.

接负载的正负极到控制器的负载接线端子。负载端可能存在电压,接线时要仔细认真,避免发生短路。

Load the positive and negative pole to the load terminal of the controller. The voltage may exist at the end of the load, and the connection should be careful to avoid the short circuit.

应该在负载正极或负极导线上接一个保险装置,安装过程中不要接通保险。安装后确认无误接通保险。

An insurance device should be attached to the load positive or negative wire, and the insurance should not be connected during the installation process. Confirm the insurance after installation.

如果负载是通过配电盘连接的,每一个负载回路中都有单独接保险,所有的负载电流不能超过控制器的额定电流。

If the load is connected through the distribution panel, every load loop is individually connected, and all load currents cannot exceed the rated current of the controller.

控制器能够适用12V、24V的离网型太阳能组件,使用开路电压不超过规定的更大输入电压的并网组件也可以。系统中太阳能组件电压要不低于系统电压。

The controller can be used for 12V and 24V off grid solar modules, and can also be used in the grid connected components with the open circuit voltage not exceeding the maximum input voltage specified. In the system, the voltage of the solar component is not lower than the system voltage.

再检查一遍所有的连接,看每一个端子的正负极是否正确,6 个接线端子是否都拧紧了。

Check all the connections again to see if the positive or negative poles of each terminal are correct, and whether the 6 terminals are all tightened.

当蓄电池给控制器供电,控制器启动时,控制器上的蓄电池LED 指示灯会点亮,注意观察是否正确。

When the battery is supplied to the controller and the controller starts, the battery LED on the controller indicates that the lamp will light and watch to see if it is correct.

本文的精彩内容来自济南力诺瑞特太阳能详细内容请点击我们的官方网站:http://www.sdlntyn.com谢谢您的到来!

The content of this wonderful from Ji'nan linuoruite solar details please click on our official website: http://www.sdlntyn.com thank you for coming!