济南力诺瑞特太阳能销售服务中心
地址:济南市天桥区粟山路76号(药山派出所对面)
电话:0531-85715890
手机:15665707182
网站:http://www.sdlntyn.com
联系人:江经理
当前位置:首页 - 新闻中心新闻中心
太阳能热水器热水管无水放出该怎么解决?
来源:http://www.sdlntyn.com 发布时间:2019-8-10 17:00:46 浏览次数:76
太阳能热水器在使用过程中会遇到各种的问题,比如说热水管无水放出(保温箱无水),电控制箱内置液位控制器无输出(红灯不亮)怎么办呢?
Solar water heater in the use process will encounter various problems, such as hot water pipes without water discharge (incubator without water), electric control tank built-in liquid level controller without output (red light does not turn on)?
济南太阳能售后服务中心建议大家先检查副水箱是否有冷水,如有,再检查控制箱内空开和漏电开关是否跳开,如好再检查液位控制器电源电源指示绿灯是否亮,如不亮应检查接线模板从左边数第一和第二接线是否有220V电源,如没有应依次往上测查;
Jinan Solar Energy After-sales Service Center recommends that you first check whether the sub-water tank has cold water, if so, then check whether the control box is empty and the leakage switch jumps off. If so, check whether the green light of the power supply indicator of the liquid level controller is on. If not, check whether the wiring template has 220V power supply from the first and second wiring on the left. If not, they should be tested in turn.
如液位控制器绿灯亮,红灯不亮,应先把接线模板上右边第二和第三的高低水位线拆除,此时如无输出或红灯亮无输出(交流接触器不启动),应检查或更换液位控制器;如有输出则应检查水位探头两线间是否有锈蚀短路或结垢,清理修复或更换水位线及探头。

If the liquid level controller is green or red, the second and third high and low water level lines on the right side of the wiring template should be removed first. If there is no output or red light and no output (AC contactor does not start), the liquid level controller should be checked or replaced; if there is output, whether there is rust short circuit or scaling between the two lines of the water level probe should be checked. Clean, repair or replace water level lines and probes.

济南太阳能售后服务中心

解决方法:(1)检查接触器线圈引线和接线板上的接线是否接触良好。
Solutions: (1) Check whether the contactor coil lead and the wiring on the wiring board are in good contact.
(2)先断开电源,用一根导线取代超温保护引线第2、4联通后,接通电源,接触器吸合,则检查是否因冷水缺水超温保护器已自动断开或烧坏;断开电源更换超温保护元件;如果接触器不吸合,断开电源去除接触器线圈引线,用万用表检查线圈,若线圈短路或断路,更换接触器,故障排除。
(2) First disconnect the power supply, replace the overtemperature protection lead with a conductor after the second and fourth connection, turn on the power supply, the contactor suction, then check whether the overtemperature protector due to cold water shortage has been automatically disconnected or burned out; disconnect the power supply to replace the overtemperature protection components; if the contactor does not suck, disconnect the power supply to remove the contactor coil lead, with 10,000 yuan Check the coil with a meter. If the coil is short-circuited or broken, replace the contactor and troubleshoot.
感谢您的阅读与观看,本文的精彩内容来自:济南太阳能售后服务中心,我们会有更多的精彩内容继续为您呈现,详情请点击:http://www.sdlntyn.com
Thank you for your reading and watching. The wonderful content of this article comes from: Jinan Solar Energy After-sales Service Center. We will continue to show you more wonderful content. For more details, please click: http://www.sdlntyn.com.