济南力诺瑞特太阳能销售服务中心
地址:济南市天桥区粟山路76号(药山派出所对面)
电话:0531-85715890
手机:15665707182
网站:http://www.sdlntyn.com
联系人:江经理
当前位置:首页 - 新闻中心新闻中心
太阳能热水器的组装步骤!
来源:http://www.sdlntyn.com 发布时间:2019-5-14 17:40:15 浏览次数:95
济南力诺瑞特太阳能提示大家,太阳辐射正午与地面夹角在一年四季中变化很大,热水器的倾角应该与当地纬度相同,才能保证在全年中太阳辐射由垂直状态左右摆动23.5°,如把热水器做成倾角可调,则稳固性降低,结构复杂,使用起来也需一年调整若干次,做成固定角为23°、33°、42°、50°几种,分别适应低中高纬度地区,提高集热效率。太阳能热水器一般由厂家或专业人员安装,但了解一下安装技术对干自己操作或监督安装员是非常必要的。
Jinan Li Norite solar energy reminds us that the angle between noon and ground of solar radiation varies greatly in the four seasons of a year. The inclination angle of water heater should be the same as that of local latitude in order to ensure that the solar radiation swings from the vertical state to the left and right by 23.5 degrees in the whole year. If the water heater is made into an adjustable inclination angle, its stability will be reduced, its structure will be complex, and it will need to be adjusted several times a year to make it work. Fixed angles of 23, 33, 42 and 50 degrees are suitable for low, middle and high latitudes to improve the efficiency of heat collection. Solar water heaters are usually installed by manufacturers or professionals, but it is necessary to understand the installation technology for their own operation or supervision of installers.
1.组装支架
1. Assembly bracket
先组装前支架,用螺栓把前支架横框竖框连接起来,再把尾座安装在前支架竖框连接孔上,然后组装后支架,如果有中间框这时要加中间框,并且要求与左右框分别在同一平面且三点同时着地,而后用连杆连接前后支架,并把桶托与前后支架用螺栓连接好,更后上铁鞋。装配完毕后,要保证后支架竖框与地面成直角。
First assemble the front bracket, connect the front bracket cross frame with bolts, then install the tailstock on the connecting hole of the front bracket vertical frame, and then assemble the rear bracket. If there is a middle frame, then add the middle frame, and require that the front and rear brackets be connected by connecting rods, and the barrel bracket and the front and rear brackets are bolted together. Finally, the rear bracket is assembled. Iron shoes. After assembly, make sure that the rear bracket frame is at right angle to the ground.
2.安装水箱与真空管
2. Installation of water tank and vacuum tube

先把水箱放置在组装完毕的支架桶托上,将水箱与桶托用螺栓连接,拧紧架子与桶托连接螺母,使水箱两端与支架左右两端距离相等,真空管中心线与前支架平面平行,然后把硅胶密封圈放入内桶翻边孔内放平,把防尘圈套在真空管上端,并在真空管上端涂水,用力均匀轻旋推入内桶,再轻轻下拉拉入尾托内,紧顶在尾托环面内胶垫上,更后将连接螺栓上螺母拧紧,再将防尘圈上推贴紧真空管孔囗处。至此,太阳能热水器主机组装完毕。

济南力诺瑞特太阳能

Firstly, the water tank is placed on the bracket of the assembled bracket, the water tank and the bracket are connected by bolts, the connecting nuts of the bracket and the bracket are tightened, so that the distance between the two ends of the water tank and the left and right ends of the bracket is equal, and the central line of the vacuum pipe is parallel to the front bracket plane. Then, the silicone rubber sealing ring is put into the flanging hole of the inner barrel, the dust-proof ring is put on the top of the vacuum pipe, and the water is applied on the upper end of the vacuum pipe The force is evenly and gently whirled into the inner barrel, then gently pulled down into the tail bracket, tightened on the inner rubber pad of the ring of the tail bracket, and finally tightened the nut on the connecting bolt, then pushed the dust-proof ring onto the hole of the vacuum pipe. So far, the solar water heater mainframe has been assembled.
3.主机的固定
3. Host Fixing
主机组装完毕后,把钢丝绳或大号钢筋套在前支架左右框及桶托左右U型环上,并用螺母拧紧,将连接好的四根钢丝绳或钢筋向热水器四角方向拉伸,在女儿墙或其他地方选择适当位置,钻孔按膨胀挂钩,将钢丝绳或 钢筋与相应膨胀挂钩用U形环牢固连接。如果确无合适位置,可浇筑钢筋混凝土块固定,如果是尖顶屋脊安装太阳热水器,情况要稍微复杂些,做特定支架,选取牢固合适的固定方式和固定位置,房脊拉钢丝绳处加上衬垫物,以免碰 或压坏屋脊。
After the main engine is assembled, the steel wire rope or large steel bar is sleeved on the left and right frame of the front support and the left and right U-ring of the barrel bracket, tightened by nuts, the four steel wires or reinforcing bars connected are stretched toward the four corners of the water heater, the appropriate position is selected in the parapet wall or other places, the expansion hook is drilled, and the steel wire rope or reinforcing bar is firmly connected with the corresponding expansion hook with the U-ring. If there is no suitable location, the reinforced concrete block can be poured to fix. If the solar water heater is installed on the top ridge, the situation will be slightly more complicated. Make a specific support, select a firm and suitable fixing way and position, and add a liner at the steel wire rope of the roof to avoid touching or crushing the roof.
以上就是济南力诺瑞特太阳能给我们整理提供的精彩内容了,不知道小伙伴们懂了没有,如果大家还有疑问欢迎咨询我们官网的客服人员:http://www.sdlntyn.com
Above is the wonderful content that Jinan Renorette Solar Energy has provided us. I don't know if our friends understand it. If you have any questions, please consult our customer service staff on our official website: http://www.sdlntyn.com.